Відео

1st thing thats not 40 yds.

To tie a bow tie

The welding is like lead I put it on trailer ramp The welding looked good but broke 7018 Trash

You might be torking the strings

Is that a nitrous valve or CO2?

I love the shit eating grin on his face. Lol

Autogenous cup walk in wrong direction 🤦

Any updates on your experience? Is it still alive?

Arm chair experts crying about short sleeves probably never welded in their life.

Just bought them and wont hold a arc without turning machine up.

Good welder though

Don’t you think you might be a reckless welder who practice ignorant? I see Acetone right buy your welder?!? Good welds though

Good review . How's warranty and service. Have a small shop so can't be down long. Also is it ok in colder weather. I don't heat shop when I'm not there. Thank you for your help.

Thanks for the video! The drivers are easy to replace, just make sure to pull off all 5 wires connected to them and rotate them 180°. In order to tune the voltage you just have to use a multi meter and screw driver. I set mine to around 800 and that seems to work fine. Also for the heat sinks I just used 3 of the original ones that were on the old driver so that the fan could fit back into the box. Thanks again for the video for $15 the drivers make a huge upgrade

Does THE tmc 2209 work the same way? Thc

Will this weld stainless sheet metal?

Adjusting voltage: 1. While the printer is switched off, unplug your stepper motor, 2. Measure and set the Vref. Vref should be measured with the motors unplugged. 3. Then switch off again the printer before plugging back the steppers. * DO not plug or unplug the stepper from the board while powered on or you might burn the controllers.. The stock stepper motor should be Nema17 1.5A max;we should set it to Inom = Irms = 1.06V.

Good video. You can weld alum With a mig spool gun, stick electrode not sure if ac or dc and also dc tig but only with certain types of alloys and only with 100% helium

You should be pushing the puddle,when I mig I make no loops or zigzag or e,just a steady straight push with maybe a short pause every 1/2" or so,don't get ahead of the puddle.

You left welder on and put torch down, you’re dangerous

You need some new wire cutters

Another reason you don't want to use high frequency start is because then Space Monsters can find you. At least that's what is says in the owners manual.

My company need one of these asap to all the welders in the place

no better sound than a 2jz with an open downpipe

Thanks for sharing great information

Thanks, I'll be watching your video again immediately, to make sure I've got this down.

Why Any Cubic don't have screens displays for their 3D printers on spare parts sell ?? if you dont do that you will have great trouble.Dont say no body said sleeping beauty

If you right handed go from left to right vice versa

Need to fix the angle of the dangle

Did the Noctua work? It doesn't push as much air as the stock so some people experienced heat creep.

Finally, an expert who can relate to new users in upgrading; excellent video instruction in a practical user approach. Thank you so much!!

they wobble because your not shooting straight. but from an angle

whats the link to those stepper drivers pls?

After the replacement of the drivers with tmc ones, do we need to upgrade firmware or chamge the cable etc.? Oe all we need is to replacement?

Nice one ;] Im thinking to swap out the drivers as well and a a fan as its too loud for no reason at all

I'm starting to see the importance of pushing the bead with aluminuml but I understand why so many people push steel . Horizontal welding sometimes I have a straight on approach but still drag.

240v for the win. I have the 24" 3500W electric griddle. It's amazing. 120v is for the birds🤣

Hard to rate on such a small volume

hola, la 211Si puede soldar aluminio en MIG? necesita algo adicional? Saludos.

Nice concise review....well done!

66 pounds that’s not a cheap unit thanks for sharing

Cheers thought we were subscribed , we are now cheers .

I hoped you also put more than a t shirt on. You don't wear gloves to just protect you from sparks, it's to protect you from uv radiation. And ffs dude, you didn't even prep the plate.

awesome Video!! do you split the filler rod to double it?

I just found this exact model for sale and am hopefully going to pick it up within a few weeks. This thing is so unbelievably quick. Cant wait to test drive it. Yours sounds amazing

Thanks for posting the Insig 7.0. Always wondered how many 5gal kegs you could fit in there. Nice setup!

Now u need change te fan or the PSU and be happy

Great video bro!!

sorry that wels sounded bad because it did not penetrate. bit would like to know how it does on 22, 24 gage car metal heaviest 18 gauge as the olde linde,s you could weld tinfoil. but seems now all this weld show be better not worse. , good video, do not like the piping in the welding as said linde is so quite

welding by you r acetone good idea not !